![]() ![]() Finally, mounting a breakaway kit makes common sense, for safety and peace of mind. LED lights show that the battery is fully charged, charging, or needs recharging. Most breakaway kits with built-in chargers also have a push-to-test feature that, with just the push of a button, will indicate the health of your battery. Our premium kits include a built-in battery charger that charges the battery anytime the trailer is connected to the tow vehicle. However, we also offer kits that make it easy to both check the battery and keep it in a full state of charge. The breakaway system is only as good as the battery, so with a basic kit you’ll have to test the battery and periodically recharge it to make sure it has the power to activate the brakes if needed. Most battery boxes are made of tough, weather resistant plastic, and we have kits with lockable cases to prevent theft of your battery. If the trailer separates from the vehicle, a cable connected to the vehicle will pull a pin from the switch, signaling the 12V battery to activate the electric trailer brakes.īeyond the basics we have kits that have added security and time saving features. The battery and switch are wired into the trailer brake system, the battery box mounted on the trailer frame, and the switch mounted near the trailer coupler. A basic kit includes a 12V battery in a protective battery box and a breakaway switch. Lock nuts and washers are then installed and tightened and the earth around the post hole replaced and tamped firmly to complete the installation.We offer a large selection of breakaway kits and parts for trailers with up to 3 axles, to help make towing safe. The top post is then nested over the end of the ground post and seated on the bolts.Slide a spacer and push-on retaining washer onto each bolt, leaving both bolts ends exposed. Place one bolt in the 1st and 5th holes in the ground post.Dig a small, shallow hole approximately 6 inches in diameter and 2 inches deep drive the ground post into the center of the hole leaving the top 4 inches above grade level exposed.For single or multiple post installations, our Breakaway System stands up to a variety of wind pressure conditions and meets the new FHWA guidelines. The system has been tested and approved for multiple post installations. This system securely nests and bolts two U-Channel posts together, yet breaks away on impact. We only use two special bolts and spacers to join the base to the top post, your installation crews can install more posts faster they will spend less time working by the side of the road, thus reducing their exposure to the risk of traffic-related injuries. Our breakaway sign post system costs considerably less than other competitive U-channel break-away systems. Systems using higher yield strength posts are brittle and can fracture at the point of impact (bumper height), scraping the bottom of the vehicle or puncturing the passenger compartment, the fuel tank, or both. All this strength, vehicle impact is transmitted through the post to the splice hardware. Our U-Channel Breakaway Sign Post System offers a tensile strength of 70,000 PSI - exactly the right strength for break-away post systems. When the assembly is struck the only part that suffers any damage is the top post making it easier to replace and install a new top post using the 3' anchor already in the ground. This breakaway system consists of the components specified below and has been designed to break away at the stub upon impact. Please note, this breakaway kit is intended for use with posts weighing 2 lbs./ft. galvanized U-Channel anchor post and one breakaway hardware set (two bolts, two spacers, two lock washers, and two standard washers). It’s very simple and saves you from digging the base out of the ground and installing a new one. Simply bolt the post back into the base post using a replacement hardware kit. This allows for the anchor post, and usually the sign post, to be reused, even after accidents occur. Upon impact, the breakaway system is designed to allow the sign post to break away from the anchor post. The galvanized finish provides the most resistance to rust and easily outlasts other types of posts – making it a great choice for when durability is a key factor. The Galvanized U-Channel Post Breakaway Kit meets FHWA safety guidelines and is AASHTO approved. Breakaway Sign Post System / Safety Splice ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |